Replacing the keyboard on your Gateway Gwtn156-1rg laptop is a relatively simple process that can be completed in a few steps. However, it is important to take precautions to avoid damaging the laptop or the keyboard. Before you begin, make sure to power off the laptop and disconnect it from any power sources. You will also need a small Phillips head screwdriver and a new keyboard.
Once you have gathered your materials, you can begin the replacement process. First, flip the laptop over and locate the screws that hold the keyboard in place. There are typically two screws located at the top of the keyboard and two at the bottom. Once you have located the screws, remove them using the screwdriver. Once the screws are removed, you can gently lift the keyboard up and away from the laptop. Be careful not to damage the ribbon cable that connects the keyboard to the laptop.
Connecting the Replacement Keyboard
Before you begin, power off the device and disconnect any external peripherals (e.g., charger, USB devices).
Flip the laptop over and locate the keyboard retaining screws. They are typically located along the top and bottom edges of the keyboard.
Using the appropriate screwdriver, carefully remove the retaining screws. Note: Do not overtighten or strip the screws.
Next, gently pry up the keyboard starting from a corner. Avoid forceful prying to prevent damage to the keyboard or laptop casing.
Disconnect the ribbon cable that connects the keyboard to the motherboard. Refer to the table below for specific details on locating the ribbon cable.
| Gateway Gwtn156-1rg Model | Ribbon Cable Location |
|---|---|
| Gwtn156-1rg | Located beneath the keyboard, in the center-right area. |
To disconnect the ribbon cable, **carefully** lift up the retaining clip and gently slide the cable out of the connector. **Avoid pulling or bending the cable.**
Insert the ribbon cable of the replacement keyboard into the connector on the motherboard, ensuring it is fully seated. Secure the cable by closing the retaining clip.
Lower the replacement keyboard into place and gently press it down to ensure all four corners are secured.
Replace the retaining screws to hold the keyboard in place. Tighten them snugly, but avoid overtightening.
Power on the device and check if the replacement keyboard is functioning correctly.
Reconnecting the Battery
Reconnecting the battery is a crucial step to ensure proper functionality of your Gateway Gwtn156-1rg laptop after replacing the keyboard. Here’s how to do it:
1. Flip and Close the Laptop
Flip the laptop upside down, ensuring it is securely closed.
2. Remove the Base Cover Screws
Locate the screws securing the base cover around the edges of the laptop. Typically, there are 9-12 screws. Use a suitable screwdriver to remove them.
3. Prepare a Plastic Card
Get a thin plastic card, such as a credit card or an ID card.
4. Pry the Cover Loose
Insert the card into a corner of the base cover, between the cover and the laptop’s chassis. Gently pry the cover loose, moving around all sides.
5. Remove the Cover
Once the cover is loose, lift it up and remove it from the laptop.
6. Locate the Battery Connector
Inside the laptop, you will see the battery. It is usually connected with a black or gray connector.
7. Disconnect the Battery
Using your fingers, gently pull up on the battery connector to disconnect the battery from the motherboard.
| Screw Length | Location |
|---|---|
| Longer Screws | Corners of the base cover |
| Shorter Screws | Middle of the edges of the base cover |
8. Reconnect the Battery
Align the battery connector with the corresponding port on the motherboard. Press down firmly until you hear a click, ensuring a secure connection.
9. Reassemble the Laptop
Place the base cover back on the laptop and secure it using the screws removed earlier. Make sure to align the screws correctly based on their lengths (refer to the table below). Tighten the screws until they are snug but avoid overtightening.
Gateway Gwtn156-1rg How To Replace Keyboard
Replacing the keyboard on a Gateway Gwtn156-1rg laptop is a relatively simple process that can be completed in a few minutes. Here are the steps on how to do it:
- Power down the laptop and unplug it from any power source.
- Close the laptop’s lid and flip it over.
- Locate the screws that are holding the keyboard in place. There are usually two or three screws on the bottom of the laptop, near the front edge.
- Remove the screws and lift the keyboard up slightly.
- Disconnect the keyboard cable from the motherboard. The cable is usually a small, white connector that is located on the bottom of the keyboard.
- Remove the keyboard from the laptop.
- Replace the new keyboard in the laptop and connect the keyboard cable to the motherboard.
- Tighten the screws that are holding the keyboard in place.
- Flip the laptop over and open the lid.
Your new keyboard should now be working properly.
People Also Ask About Gateway Gwtn156-1rg How To Replace Keyboard
How do I know if my Gateway Gwtn156-1rg keyboard is broken?
There are a few signs that your Gateway Gwtn156-1rg keyboard may be broken. These include:
- Keys that are not working properly or are sticking.
- Keys that are missing or have come loose.
- The keyboard is not responding at all.
Can I replace the keyboard on my Gateway Gwtn156-1rg myself?
Yes, you can replace the keyboard on your Gateway Gwtn156-1rg yourself. However, it is important to follow the instructions carefully to avoid damaging your laptop.
Where can I buy a replacement keyboard for my Gateway Gwtn156-1rg?
You can purchase a replacement keyboard for your Gateway Gwtn156-1rg from a variety of online retailers, such as Amazon.com or Newegg.com. You can also find replacement keyboards at some local computer stores.
