The Ego Power+ String Trimmer is a powerful and versatile tool that can help you keep your lawn looking its best. It is easy to use, and it comes with a variety of features that make it a great choice for homeowners of all levels. One of the most important things to know about using an Ego string trimmer is how to load the line. In this article, we will provide you with step-by-step instructions on how to do this, as well as some tips for troubleshooting common problems.

To load the line on your Ego string trimmer, you will need to:

Unplug the trimmer from the power source.
Flip the trimmer over so that the bottom is facing up.
Locate the line spool cover and remove it.
Insert the new line into the spool.
Wrap the line around the spool in a clockwise direction.
Replace the line spool cover.
Trim the excess line off of the spool.

Once you have loaded the line, you can plug the trimmer back into the power source and start using it. If you are having trouble loading the line, there are a few things that you can check:

Make sure that the line is the correct size for your trimmer.
Make sure that the line is wound in the correct direction.
Make sure that the line spool cover is properly installed.

If you are still having trouble, you can contact Ego customer service for assistance.

Inserting the Trimmer Line

To ensure optimal performance and safety, it is crucial to correctly insert the trimmer line into your Ego trimmer. Follow these detailed steps to achieve a perfect line insertion:

Unplug the trimmer: Before touching any components, disconnect the trimmer from the power source for safety.
Locate the line hole: On the trimmer head, identify the line hole, which typically has two slots or hooks.
Cut the line to length: Measure and cut a piece of trimmer line to the desired length, approximately 10-15 feet. You can adjust the length later if needed.
Thread the line through the hole: Insert one end of the trimmer line into one of the slots or hooks on the line hole. Ensure that the line is fully seated and aligned with the hole.
Wind the line onto the spool: While holding the free end of the line, start winding it clockwise around the spool inside the trimmer head. Apply even tension as you wind to create a firm but not overly tight coil.
Secure the line: Once the spool is fully wound, secure the excess line by wrapping it around the designated hook or keeper on the trimmer head.
Repeat for the second line: Insert the other end of the trimmer line into the remaining slot or hook and follow the same winding and securing process.
Check the line length: After inserting both lines, extend them to their full length and check if they are equal in size. Adjust the line length as necessary.
Plug in and trim: Once the lines are properly inserted and adjusted, reconnect the trimmer to the power source and start trimming your lawn with ease.

Winding the Line onto the Spool

Before you can use your Ego trimmer, you’ll need to wind the line onto the spool. Here’s how to do it:

Step 1: Open the spool cover

Locate the spool cover on the side of the trimmer head. Press the release button and lift the cover off.

Step 2: Insert the line into the spool

Hold the spool in one hand and the line in the other. Insert the end of the line into the small hole on the end of the spool. Make sure the line is facing the correct direction, as shown in the diagram below.

Diagram:

Step 3: Wind the line onto the spool

Use your fingers to wrap the line around the spool, making sure to keep it taut. Continue winding until the spool is full.

Step 4: Secure the line

Once the spool is full, cut the line to the desired length. Then, insert the end of the line into the slot on the side of the spool and pull it tight.

Step 5: Close the spool cover

Place the spool cover back on the trimmer head and press down until it clicks into place.

Tips:

Use a high-quality trimmer line for best results.
If the line is too short, it may not feed properly into the trimmer head.
If the line is too long, it may get tangled or cause the trimmer to overheat.

Securing the Line in the Notch

Insert the remaining line into the feed hole on the trimmer head and pull it until you feel tension. Grasp the line and use your thumb to press it firmly into the notch on the spool. Ensure that the line is seated properly and held securely in place.

Tips for Securing the Line:
– Use a firm grip when pressing the line into the notch.
– Check that the line is not twisted or tangled.
– If the line is loose, adjust the tension by turning the knob on the trimmer head.

Once the line is secured, feed it through the trimmer head’s guide hole and out the cutting head’s opening. Trim any excess line, leaving about 6 inches exposed beyond the cutting head.

Now that the line is securely loaded, your Ego trimmer is ready for use. Remember to wear appropriate safety gear, such as gloves and eye protection, while operating the trimmer.

Threading the Line through the Eyelet

1. **Locate the eyelet.** The eyelet is a small hole located on the top of the trimmer head. It is typically made of metal or plastic.

2. **Cut a length of trimmer line.** The line should be approximately 15-20 feet long. Use a sharp knife or scissors to cut the line cleanly.

3. **Insert the trimmer line into the eyelet.** Start by feeding the line through the eyelet from the bottom up. Push the line through until it reaches the other side.

4. **Feed the line around the spool.** Once the line is through the eyelet, guide it around the spool in a clockwise direction. Make sure the line is evenly wrapped around the spool, avoiding any tangles or overlaps.

Here are some additional tips for threading the line through the eyelet:

Tip	Description
Use a sharp knife or scissors	This will help to create a clean cut that will not fray the end of the line.
Feed the line through the eyelet from the bottom up	This will help to prevent the line from getting stuck in the eyelet.
Wrap the line around the spool in a clockwise direction	This will help to ensure that the line is evenly distributed and will not tangle.

Once you have threaded the line through the eyelet and wrapped it around the spool, you are ready to start trimming your lawn.

Connecting the Line to the Cutter

Loading the line into your Ego trimmer is a simple process that can be completed in a few minutes. By following these steps, you can ensure that your trimmer is properly loaded and ready to use.

Locate the trimmer head.
Remove the cover from the trimmer head.
Insert the line into the hole in the center of the trimmer head.
Feed the line through the slot in the cutter.

Wrap the line around the cutter head in a clockwise direction.
Pull the line through the hole in the cutter head.
Trim the excess line.

Replace the cover on the trimmer head.

Wrapping the Line Around the Cutter Head

When wrapping the line around the cutter head, it is important to ensure that the line is wrapped in a clockwise direction. This will help to prevent the line from unwinding while you are using the trimmer. To ensure a secure hold, wrap the line around the cutter head at least twice.

Pulling the Line Through the Hole in the Cutter Head

Once you have wrapped the line around the cutter head, you need to pull the line through the hole in the cutter head. To do this, simply use your fingers to pull the line through the hole. Make sure to pull the line all the way through so that it is securely in place.

Trimming the Excess Line

Once the line is pulled through the hole in the cutter head, you need to trim the excess line. To do this, simply use a pair of scissors to cut the line off at the desired length. Make sure to leave enough line so that you can easily grip the line when you are using the trimmer.

Adjusting Line Length and Tension

Proper line length and tension are crucial for optimal trimmer performance. Follow these steps to adjust both:

Line Length

1. Start the trimmer and let the line extend until it reaches the desired length.
2. Mark the desired length on the spool with a marker or tape.
3. Stop the trimmer and remove the spool.
4. Cut the line to the marked length using sharp shears.
5. Reinstall the spool and feed the line back into the trimmer.

Line Tension

1. Turn the tension adjustment knob clockwise to increase tension or counterclockwise to decrease it.
2. Start the trimmer and observe the line as it feeds out.
3. Adjust the tension until the line feeds smoothly and doesn’t jam.
4. **Troubleshooting:**

Troubleshooting Loading Issues

1. Check the trimmer head

Ensure that the trimmer head is properly attached and the trimmer line is securely loaded. If the trimmer line is worn or broken, replace it with a new one.

2. Inspect the spool

Examine the trimmer spool to ensure that it is not damaged or cracked. If the spool is damaged, it may need to be replaced.

3. Clean the trimmer head

Remove any debris or grass clippings that may have accumulated around the trimmer head. This can block the line from feeding properly.

4. Adjust the spool tension

The spool tension may need to be adjusted to ensure that the line is fed at the correct speed. Refer to the user manual for specific instructions on how to adjust the spool tension.

5. Check the battery

Ensure that the battery is fully charged or replaced with a charged one. A weak or depleted battery may not provide enough power to feed the trimmer line.

6. Reset the trimmer

Sometimes, a simple reset can resolve loading issues. Turn off the trimmer, remove the battery, and wait a few minutes. Reinsert the battery and turn on the trimmer.

7. Contact customer support

If the above troubleshooting steps do not resolve the issue, contact Ego customer support for further assistance. They can provide additional guidance or arrange for a repair or replacement if necessary.

Tips for Optimal Line Performance

Loading your Ego trimmer correctly is essential for optimal performance and longevity of the line. Here are a few tips to help you get the best results:

1. Use the Correct Line Type

Ego trimmers are designed to use a specific type of line, typically 0.095 inches in diameter. Using the incorrect line type can damage the trimmer or reduce its performance.

2. Wind the Line in the Correct Direction

The line should be wound onto the spool in the direction specified by the arrow on the spool. Winding the line in the incorrect direction can cause the line to break prematurely.

3. Fill the Spool Evenly

The line should be evenly distributed around the spool. Overfilling the spool can cause the line to bind and break, while underfilling it can reduce the trimmer’s cutting efficiency.

4. Trim the Excess Line

Once the spool is filled, trim any excess line that extends beyond the outer edge of the spool. This will prevent the line from tangling or catching on obstacles.

5. Use a Line Winder

A line winder can help you load the line quickly and evenly. Line winders are available at most hardware stores for a few dollars.

6. Test the Line Tension

The line tension should be adjusted so that the line feeds out smoothly when the trimmer is running. If the tension is too tight, the line may break prematurely. If the tension is too loose, the line may not feed out properly.

7. Clean the Trimmer Head Regularly

Over time, the trimmer head can become clogged with grass and debris. This can reduce the trimmer’s performance and cause the line to break prematurely. Cleaning the trimmer head regularly will help keep it running smoothly.

8. Troubleshooting Line Problems

If you are experiencing problems with your Ego trimmer line, consult the troubleshooting table below:

Issue	Possible Cause	Solution
Line is too loose	Inadequate tension	Increase tension
Line is too tight	Excessive tension	Decrease tension
Line jams	Too much tension or tangled line	Release tension or untangle line

Problem	Possible Cause	Solution
Line breaks prematurely	Incorrect line type	Use the correct line type specified by Ego
Line doesn’t feed out properly	Line tension too tight	Adjust the line tension according to the manufacturer’s instructions
Line breaks when hitting obstacles	Excess line	Trim any excess line that extends beyond the outer edge of the spool
Trimmer head clogged	Grass and debris buildup	Clean the trimmer head regularly to prevent clogging

Using Different Line Types

Ego trimmers offer a variety of line types to accommodate different cutting needs. Here’s a guide to selecting and loading the optimal line for your task:

Nylon Monofilament Line

Monofilament line is ideal for general-purpose trimming and edging. It’s lightweight, flexible, and easy to reload.

Twisted Nylon Line

Twisted nylon line provides increased durability over monofilament line. It’s suitable for tackling thicker weeds and brush.

Square Nylon Line

Square nylon line is the most durable and aggressive line type. It’s designed for heavy-duty cutting, like thick grass and weeds.

Quad Feed Line

Quad feed line is a unique, four-sided line that’s designed to reduce noise and vibration while enhancing cutting efficiency. It’s an excellent choice for extended use and sensitive areas.

Safety Precautions for Line Loading

1. Wear Eye Protection

Always wear ANSI-approved safety glasses or goggles when loading trimmer line to protect your eyes from flying debris.

2. Keep Hands Away from the Spool

Keep your hands away from the rotating spool when loading line. The spool can cause serious injury if it catches your fingers.

3. Turn Off the Trimmer

Before loading line, turn off the trimmer and unplug it from the power source. This will prevent the trimmer from starting accidentally and causing injury.

4. Clean the Spool Area

Before loading line, clean the spool area of any debris or grass clippings. Debris can prevent the line from loading properly and can cause the trimmer to jam.

5. Use the Correct Line Size

Refer to your trimmer’s manual for the recommended line size. Using the wrong size line can damage the trimmer.

6. Insert the Line into the Spool

Insert the end of the line into the hole on the side of the spool. Make sure the line is fully inserted and that it is not twisted.

7. Wrap the Line Around the Spool

Wrap the line around the spool in a clockwise direction. Make sure the line is evenly wrapped and that there are no gaps.

8. Secure the Line

Secure the line to the spool by wrapping the end of the line around the outside of the spool and threading it through the hole. This will prevent the line from unwinding.

9. Check the Tension

Check the tension of the line by pulling on it lightly. The line should be taut but not too tight. If the line is too tight, it can break easily. If the line is too loose, it can slip off the spool.

10. Inspect the Trimmer before Use

Before using the trimmer, inspect it for any damage or loose parts. Make sure the line is loaded correctly and that the trimmer is properly assembled.

Item	Safety Precaution
Eye protection	Wear ANSI-approved safety glasses or goggles.
Hands	Keep hands away from the rotating spool.
Power source	Turn off the trimmer and unplug it from the power source.
Spool area	Clean the spool area of any debris or grass clippings.
Line size	Use the correct line size for your trimmer.
Line insertion	Insert the end of the line into the hole on the side of the spool.
Line wrapping	Wrap the line around the spool in a clockwise direction.
Line securing	Secure the line to the spool by wrapping the end of the line around the outside of the spool and threading it through the hole.
Line tension	Check the tension of the line by pulling on it lightly.
Trimmer inspection	Inspect the trimmer for any damage or loose parts before use.

Ego Trimmer How To Load

To load an Ego trimmer, follow these steps:

Remove the battery from the trimmer.
Locate the line spool on the trimmer head.
Press the release button on the line spool and remove the spool.
Unwind the new trimmer line from the spool and cut it to the desired length.
Wrap the trimmer line around the spool in a clockwise direction.
Replace the spool on the trimmer head and press the release button to secure it.
Insert the battery into the trimmer.
Pull the starter cord to start the trimmer.