Imagine the convenience of having clean, refreshing water right at your fingertips. A refrigerator with a built-in water filter makes this a reality, but what happens when it’s time to replace the filter? If you own a Frigidaire refrigerator, fret not! Changing the water filter is a simple and straightforward process that can be completed in just a few minutes. Let’s delve into the steps involved to ensure a seamless and hassle-free experience.
Firstly, locate the water filter housing. It’s typically found inside the refrigerator compartment, either on the top or bottom shelf. Once identified, gently squeeze the release button or lever located on the housing. This action will release the filter from its locked position, allowing you to pull it straight down. Voila! You’ve successfully removed the old water filter and are ready to replace it with a fresh one.
Now, it’s time to insert the new water filter. Align the filter with the housing and firmly push it into place until it clicks and locks securely. You’ll know it’s properly installed when the release button or lever snaps back into its initial position. Remember, it’s crucial to replace the water filter every six months or as recommended by the manufacturer to ensure optimal water quality and prevent any potential issues down the road.
Removing the Filter Housing Cap
To remove the filter housing cap, follow these steps:
- Turn off the water supply to the refrigerator.
- Open the refrigerator door and locate the filter housing cap at the top right corner of the refrigerator compartment.
Cap Variant Removal Instructions Cap with Tabs Press the tabs on the sides of the cap and pull down. Cap with Button Press the button on top of the cap and pull down. - Pull the cap down and remove it.
Optional: It is advisable to have a bowl or towel underneath the filter housing to catch any residual water that may spill during the removal process.
- Discard the old filter and install a new one.
- Take the new filter out of its packaging and remove the protective cap from the bottom of the filter.
- Align the new filter with the slots in the filter housing and push it up into place until it clicks.
- Replace the filter housing cap by aligning it with the housing and pushing it up until it clicks into place.
- Turn on the water supply to the refrigerator and run water through the filter for about 5 minutes to flush out any air or impurities.
Twisting Out the Old Filter
The old filter can be removed by twisting it counterclockwise. Ensure the water supply is turned off before performing this step. Locate the filter housing and grasp the filter. Turn the filter counterclockwise until it loosens and can be removed. Be cautious of any remaining water that may leak out when the filter is extracted.
If you encounter difficulty twisting the filter, try using a pair of pliers or a wrench for better grip. Place a cloth or towel around the filter to prevent scratches or damage during the removal process.
Once the old filter is removed, inspect it for any signs of damage or deterioration. Dispose of the old filter properly and continue to the next step of installing the new filter.
Tip: It is recommended to replace the water filter every six months or as per the manufacturer’s instructions to ensure optimal water quality and filtration performance.
Safety Precautions:
| Turn off the water supply before removing the filter to prevent any spills or leaks. |
| Wear gloves if necessary to protect your hands from any residue or dirt present on the filter. |
Inserting the New Filter
**Step 1: Locate the Water Filter Compartment**
Find the compartment located inside the refrigerator door. It may be covered by a plastic door.
**Step 2: Remove the Old Filter**
Grip the old filter by its handle and pull it straight down to remove it from the compartment.
**Step 3: Remove the Filter Cap**
Locate the small cap at the bottom of the filter. Twist it counterclockwise to remove it.
**Step 4: Insert the New Filter into the Cap**
Align the alignment notch on the new filter with the notch on the cap. Push the filter into the cap until it clicks into place.
**Step 5: Install the Filter Assembly**
Place the filter assembly into the compartment. Make sure it is facing the correct direction.
**Step 6: Flush the Water Line**
Dispense water from the dispenser for several minutes to remove any air from the line.
**Step 7: Reset the Filter Indicator**
If the refrigerator has a filter indicator light, you may need to reset it after installing the new filter. Check the refrigerator’s user manual for specific instructions on how to reset the indicator.
| Reset Method | Compatible Refrigerator Models |
|---|---|
| Press and hold the "Reset" button for 5 seconds | FRF2311MW1, FRF2311MS1 |
| Press the "Filter Reset" button on the control panel | FFHD2277ED1, FFRS2622AS2 |
| Press the "Water Filter" button on the dispenser | FRS26S5FW0, GLRS26FXXG0 |
How to Remove a Frigidaire Water Filter
Step 1: Locate the Water Filter
The water filter is typically located behind the grille at the bottom of the refrigerator.
Step 2: Grip the Filter
Grasp the filter firmly with both hands.
Step 3: Turn the Filter Counterclockwise
Twist the filter counterclockwise to loosen it.
Step 4: Pull the Filter Out
Once the filter is loose, pull it straight out of the housing.
Step 5: Insert the New Filter
Align the new filter with the housing and push it into place.
Step 6: Turn the Filter Clockwise
Twist the filter clockwise to tighten it.
People Also Ask
How often should I replace my Frigidaire water filter?
Replace the filter every 6 months, or more frequently if you have hard water.
Can I use a generic water filter in my Frigidaire refrigerator?
It is recommended to use a Frigidaire純正水フィルター for optimal performance and water quality.
What are the signs that my Frigidaire water filter needs to be replaced?
Signs include decreased water flow, discolored or cloudy water, or a strange taste or smell.
