As a homeowner, it’s frustrating when you realize you’ve forgotten the programming code for your Schlage keypad lock. Without the code, you’re locked out of your home, feeling both anxious and helpless. But don’t despair – there’s a solution. This guide will walk you through the process of resetting your Schlage keypad lock without a programming code. With careful guidance and clear instructions, you’ll regain access to your home without the need for a locksmith or expensive replacement parts. Let’s embark on this journey of securing your home and restoring your peace of mind.
To begin the process, you’ll need to gather a few essential tools: a small flathead screwdriver and a 9-volt battery. These items will enable you to access the lock’s internal components and reset the system. Once you have the necessary tools, locate the small hole on the bottom of the keypad. Carefully insert the flathead screwdriver into the hole and press down gently until you hear a click. This action will release the keypad from the lock, allowing you to remove it.
With the keypad removed, you’ll gain access to the lock’s interior. Locate the small black button on the circuit board, usually situated near the battery compartment. Press and hold the button for approximately 10 seconds. While holding the button, simultaneously insert the 9-volt battery into the compartment. Keep both the button and the battery in place for another 10 seconds. This sequence of actions will reset the lock, erasing any existing programming or user codes. Afterward, remove the battery and reattach the keypad to the lock. Your Schlage keypad lock is now reset, ready for you to establish new programming codes and regain control of your home’s security.
Locate the Reset Button
Step 1: Identify the Lock Model
To determine the reset procedure, you need to know the specific Schlage keypad lock model you have. Consult the user manual or check the lock’s packaging or website for model identification.
Step 2: Physical Button Reset
Most physical button reset options are located on the back of the lock’s keypad. Remove the battery cover to reveal the reset button beneath it. Alternatively, some models may have the button hidden behind a small flap on the keypad itself.
Step 3: Reset Button Position and Operation
The location and activation method of the reset button vary depending on the model:
| Lock Model | Reset Button Location | Operation |
|---|---|---|
| Schlage Encode Plus | Beneath battery cover | Press and hold for 10 seconds |
| Schlage Connect | Behind keypad flap | Insert paperclip and press for 10 seconds |
| Schlage BE365 | Beneath battery cover | Press and hold for 15 seconds |
Press and Hold the Reset Button
It is possible to reset a Schlage keypad lock without the programming code by holding down the reset button for a certain amount of time.
How to Reset a Schlage Keypad Lock Without the Programming Code
Here are the steps on how to reset a Schlage keypad lock by pressing and holding the reset button:
1. Locate the reset button. The reset button is usually located on the back or bottom of the keypad lock.
2. Press and hold the reset button for 10 seconds. The keypad lock will beep and the lights will flash.
3. Release the reset button. The keypad lock will now be reset to factory settings.
You will need to reprogram the lock with a new programming code.
Here are some additional tips for resetting a Schlage keypad lock without the programming code:
• If you cannot find the reset button, you can try removing the battery from the keypad lock. Wait for 10 seconds and then reinsert the battery. This will reset the keypad lock to factory settings.
• If you have lost the programming code and cannot reset the keypad lock, you can contact Schlage customer service for assistance. They may be able to provide you with a new programming code.
| Steps to Reset Schlage Keypad Lock | |
|---|---|
| Locate the reset button | The reset button is typically found on the backside or beneath the keypad lock |
| Press and hold the reset button for 10 seconds | The keypad will produce a beeping sound, and the lights will blink |
| Release the reset button | The keypad will revert to its factory settings |
Remove All Codes Manually
This method is the most effective way to reset your Schlage keypad lock without a programming code. However, it requires you to remove the lock from the door and disassemble it. Here are the steps:
- Remove the lock from the door: Locate the two screws on the inside of the door that hold the lock in place. Remove the screws and pull the lock away from the door.
- Disassemble the lock: Remove the battery cover on the back of the lock. Inside the battery compartment, you will find two screws that hold the lock together. Remove the screws and carefully separate the two halves of the lock.
- Remove the keypad: Once the lock is disassembled, you will see the keypad. It is held in place by two screws. Remove the screws and lift the keypad off.
- Clear the codes: On the back of the keypad, you will find a small hole. Insert a paperclip or similar object into the hole and press the button inside. This will clear all of the codes from the lock.
- Reassemble the lock: Once the codes are cleared, reassemble the lock in reverse order. Start by putting the keypad back on and securing it with the screws. Then, put the two halves of the lock together and secure them with the screws. Finally, put the battery cover back on.
- Reinstall the lock: Put the lock back onto the door and secure it with the screws.
- Program new codes: Once the lock is reinstalled, you can program new codes by following the instructions in the user manual.
Reset the Lock to Factory Settings
If you have lost your programming code or have forgotten the default code, you can reset your Schlage keypad lock to its factory settings. This will erase all of the codes that you have programmed into the lock, including the master code. Once the lock is reset, you will need to program a new master code before you can use it again.
To reset your Schlage keypad lock to its factory settings:
- Press the “Schlage” button on the bottom of the keypad.
- Enter the six-digit reset code. The default reset code is 111111. If you have changed the default code, you will need to enter the code that you programmed.
- Press the “#” key.
- The lock will beep and the red LED will flash. This indicates that the lock has been reset to its factory settings.
- Program a new master code.
Programming a New Master Code
To program a new master code:
- Press the “Schlage” button on the bottom of the keypad.
- Enter the six-digit reset code. The default reset code is 111111. If you have changed the default code, you will need to enter the code that you programmed.
- Press the “#” key.
- Enter your new six-digit master code.
- Press the “#” key again.
- The lock will beep and the green LED will flash. This indicates that the new master code has been programmed.
| **Programming a New Master Code** |
|
To program a new master code:
|
Reset the Handle
If the handle on your Schlage keypad lock is not working properly, you may need to reset it. To do this, first remove the battery cover on the back of the lock. Next, press and hold the reset button for about 10 seconds. The reset button is located on the inside of the battery cover, next to the battery terminals. After 10 seconds, release the reset button and reinsert the battery cover. The handle should now be reset and working properly.
Here are the steps in more detail:
- Remove the battery cover on the back of the lock.
- Press and hold the reset button for about 10 seconds. The reset button is located on the inside of the battery cover, next to the battery terminals.
- Release the reset button and reinsert the battery cover.
- The handle should now be reset and working properly.
If you are still having problems with the handle, you may need to contact Schlage customer service.
How To Reset Schlage Keypad Lock Without Programming Code
If you have lost or forgotten your Schlage keypad lock programming code, you can still reset the lock without it. Here are the steps on how to do it:
- Remove the battery cover from the inside of the lock.
- Remove the batteries from the lock.
- Press and hold the reset button on the inside of the lock for 10 seconds.
- Release the reset button.
- Reinsert the batteries into the lock.
- Replace the battery cover.
- The lock is now reset to the factory default settings.
People Also Ask
How do I reset my Schlage keypad lock if I have lost the programming code?
You can reset your Schlage keypad lock without the programming code by following the steps outlined above.
What is the factory default code for a Schlage keypad lock?
The factory default code for a Schlage keypad lock is 1234.
How do I change the programming code on my Schlage keypad lock?
To change the programming code on your Schlage keypad lock, you will need to enter your current programming code followed by the new programming code. You can then press the # key to save the new code.
